계측제품

LeCroy
LabMaster 10Zi
WaveMaster 8Zi-B
WavePro HD
WaveRunner9000
WaveRunner8000HD
MDA8000HD
HDO6000A
HDO4000A
WaveSurfer 4000HD
WaveSurfer510
WaveSurfer3000Z
T3DSO2000
T3DSO1000
Serial Data Analyzer
Disk Drive Analyzer
자동차 테스트 솔루션
혼합 신호 오실로스코프
WaveRunner8000[단종]
WavrRunner6Zi[단종]
HDO9000[단종]
HDO8000A[단종]
HDO6000[단종]
HDO4000[단종]
WaveSurfer3000[단종]
WaveSuffer MXs-B[단종]
WaveAce[단종]
WaveExpert[단종]
WaveJet[단종]
WavePro 7Zi-A[단종]
LabMaster9Zi-A[단종]
MDA800[단종]
MDA800A[단종]
HDO6104A
HDO6054A
HDO6034A
HDO6104A
분    류오실로스코프
모델명HDO6104A
- 대역폭 : 1 GHz
- 채널 : 4 Ch
- 분해능 : 12-bit
- 샘플속도 : 10 GS/s
- 메모리 : 50 Mpts/Ch
- High Definition Oscilloscope
- 12.1"" WXGA Color Display
DATA SHEET 

상품상세 정보

  • 4 input channels
  • 16 digital channels (with –MS models)
  • 12-bit ADC resolution, up to 15 bits with enhanced resolution
  • Up to 10 GS/s with Enhanced Sample Rate
  • 350 MHz, 500 MHz, and 1 GHz bandwidths
  • ±10 V applied offset with high gain settings
  • Long Memory - up to 250 Mpts/Ch
  • MAUI with OneTouch user interface
  • Exceptional Serial Data Tools
  • Powerful, Deep Toolbox

     

     

     

     

    Vertical - Analog Channels
    Analog Bandwidth (Max)1 GHz
    Analog Bandwidth @ 50 Ω (-3 dB) (ProBus Input)1 GHz(≥1 mV/div)
    Analog Bandwidth @ 1 MΩ (-3 dB) (ProBus Input)500 MHz (typical)
    Rise Time (10-90%, 50 Ω)450 ps (typical)
    Rise Time (20-80%, 50 Ω)340 ps (typical)
    Input Channels4
    Vertical Resolution12 bits; up to 15 bits with enhanced resolution (ERES)
    Effective Number of Bits (ENOB)8.4 bits
    Vertical Noise Floor (1 mV/div)145 uVrms
    Vertical Noise Floor (2 mV/div)145 uVrms
    Vertical Noise Floor (5 mV/div)150 uVrms
    Vertical Noise Floor (10 mV/div)155 uVrms
    Vertical Noise Floor (20 mV/div)185 uVrms
    Vertical Noise Floor (50 mV/div)275 uVrms
    Vertical Noise Floor (100 mV/div)500 uVrms
    Vertical Noise Floor (200 mV/div)1.75 mVrms
    Vertical Noise Floor (500 mV/div)2.75 mVrms
    Vertical Noise Floor (1 V/div)4.90 mVrms
    Sensitivity50 Ω: 1 mV-1 V/div, fully variable; 1 MΩ: 1 mV-10 V/div, fully variable
    DC Vertical Gain Accuracy (Gain Component of DC Accuracy)±(0.5%) F.S, offset at 0 V
    Channel-Channel IsolationDC-200 MHz: 60 dB (>1000:1), 200-500 MHz: 50 dB (>300:1),500 MHz up to rated bandwidth: 40 dB (>100:1)(For any two input channels, same v/div settings, typical)
    Offset Range50 Ω±1.6 V @ 1 mV - 4.95 mV/div±4 V @ 5 mV - 9.9 mV/div±8 V @ 10 mV - 19.8 mV/div±10 V @ 20 mV - 1 V/div1 MΩ±1.6 V @ 1 mV - 4.95 mV/div±4 V @ 5 mV - 9.9 mV/div±8 V @ 10 mV - 19.8 mV/div±16 V @ 20 mV - 100 mV/div±80 V @ 102 mV - 198 mV/div±160 V @ 200 mV - 1 V/div±400 V @ 1.02 V - 10 V/div
    DC Vertical Offset Accuracy±(1.0% of offset setting + 0.5%FS + 0.02% of max offset + 1mV)
    Maximum Input Voltage50 Ω: 5 Vrms,1 MΩ: 400 V max (DC + Peak AC ≤ 10 kHz)
    Input Coupling1 MΩ: AC, DC, GND; 50 Ω: DC, GND
    Input Impedance1 MΩ ± 2.0% || 15 pF, 50 Ω ± 2.0%
    Bandwidth Limiters20MHz, 200MHz
     
    Horizontal - Analog Channels
    TimebasesInternal timebase common to 4 input channels; an external clock may be applied at the auxiliary input
    Acquisition ModesReal-time, Roll, Random Interleaved Sampling (RIS), Sequence
    Time/Division Range20 ps/div - 5 ks/div with standard memory (up to 10 ks/div with -L memory, 25 ks/div with -XL memory);RIS available at ≤ 10 ns/div; Roll Mode available at ≥ 100 ms/div and ≤ 5 MS/s
    Clock Accuracy+/-2.5ppm + 1.0ppm/year from calibration
    Sample Clock Jitterup to 10ms Acquired Time Range:280fsrms (Internal Timebase Reference)
    Delta Time Measurement Accuracy\sqrt{2}*\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2) (RMS)+(clock accuracy*reading)(seconds)
    Jitter Measurement Floor\sqrt{(\frac{Noise}{SlewRate})^2+(Sample Clock Jitter)^2\; seconds\; rms\; (TIE)}
    Jitter Between Channels2psrms (TIE, typical)
    Channel-Channel Deskew Range±9 x time/div. setting, 100 ms max., each channel
    External Timebase Reference (Input)10MHz +/-25ppm at 0 to 10dBm into 50 Ohms
    External Timebase Reference (Output)10MHz, 2.0 dBm +/-1.5 dBm, sinewave synchronized to reference being used (internal or external reference)
    External ClockDC to 100 MHz; (50 Ω/1 MΩ), EXT BNC input, Minimum rise time and amplitude requirements apply at low frequencies.
     
    Acquisition - Analog Channels
    Sample Rate (Single-shot)10 GS/s on 4 Ch with Enhanced Sample Rate
    Sample Rate (Repetitive)125 GS/s for repetitive signals (20 ps/div to 10 ns/div)
    Memory Length (4 Ch / 2 Ch / 1Ch)(Number of Segments)50M / 50M / 50M(30,000)
    Memory Length Options (4 Ch / 2 Ch / 1Ch)(Number of Segments)L- Option: 100M / 100M / 100M(60,000)XL - Option:250M / 250M / 250M(65,000)
    Intersegment Time1 µs
    AveragingSummed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
    Enhanced Resolution (ERES)From 12.5 to 15 bits vertical resolution
    Envelope (Extrema)Envelope, floor, or roof for up to 1 million sweeps
    InterpolationLinear or Sin x/x (2 pt and 4 pt); 5 or 10 GS/s Enhanced Sample Rate defaults to 2pt or 4pt Sin x/x respectively
     
    Triggering System
    Modes Normal, Auto, Single, and Stop
    SourcesAny input channel, Ext, Ext/10, or line; slope and level unique to each source (except line trigger)
    CouplingDC, AC, HFRej, LFRej
    Pre-trigger Delay0-100% of memory size (adjustable in 1% increments of 100 ns)
    Post-trigger Delay0-10,000 Divisions in real time mode, limited at slower time/div settings or in roll mode
    Hold-offFrom 2 ns up to 20 s or from 1 to 99,999,999 events
    Trigger and Interpolator Jitter≤ 3.5 psrms (typical)<0.1 ps RMS (typical, software assisted)
    Internal Trigger Level Range±4.1 div from center (typical)
    External Trigger Level RangeExt (±0.4 V); Ext/10 (±4 V)
    Maximum Trigger Rate1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
    Trigger Sensitivity with Edge Trigger ProBus Inputs2 div @ < 1 GHz1.5 div @ < 500 MHz1 div @ < 200 MHz0.9 div @ < 10 MHz(DC, AC, and LFRej coupling, ≥ 2 mV/div, 50 Ω)
    Trigger Sensitivity with Edge Trigger (Aux Input)2 div @ < 1 GHz1.5 div @ < 500 MHz1 div @ < 200 MHz0.9 div @ < 10 MHz(DC, AC, and LFRej coupling)
    Max. Trigger Frequency, SMART Trigger 1GHz
     
    Trigger Types
    EdgeTriggers when signal meets slope (positive, negative, or either) and level condition.
    WidthTriggers on positive or negative glitches with selectable widths.minimum width 1.5ns, Maximum Width: 20s
    GlitchTriggers on positive or negative glitches with selectable widths. minimum width 1.5ns, Maximum Width: 20s
    WindowTriggers when signal exits a window defined by adjustable thresholds
    PatternLogic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
    TV-Composite VideoTriggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative).
    RuntTrigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
    Slew RateTrigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
    IntervalTriggers on intervals selectable between 1 ns and 20 s.
    DropoutTriggers if signal drops out for longer than selected time between 1 ns and 20 s.
    Measurement TriggerSelect from a large number of measurement parameters trigger on a measurement value with qualified limits. Can be used as only trigger or last event in a Cascade Trigger.
    Multi-Stage: Qualified (Timeout or State/Edge Qualified)Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is selectable by time or events.
    Triggers with Exclusion TechnologyTrigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
    Multi-Stage: Qualified FirstIn Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events.
    Multi-Stage: Cascade (Sequence) Trigger, CapabilityArm on "A" event, then Trigger on "B" event. Or Arm on "A" event, then Qualify on "B" event, and Trigger on "C" event.
    Multi-Stage: Cascade (Sequence) Trigger, TypesCascade A then B: Edge, Window, Pattern (Logic) Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage B only.Cascade A then B then C (Measurement): Edge, Window, Pattern (Logic), Width, Glitch, Interval, Dropout, or Measurement. Measurement can be on Stage C only.Cascade A then B then C: Edge, Window, Pattern (Logic)
    Multi-Stage: Cascade (Sequence) Trigger, HoldoffHoldoff between A and B or B and C is selectable by time or number of events.Measurement trigger selection as the last stage in a Cascade precludes a holdoff setting between the prior stage and the last stage.
    TriggerScanA Trigger Trainer analyzes the waveforms, identifies normal behavior, and then sets up a large set of rare event smart trigger setups that target abnormal behavior. The trainer ‘learns’ trigger setups based on slew rates, periods, amplitudes outside of a range and then applies them sequentially.
     
    Low Speed Serial Protocol Trigger (Optional)
    Supported ProtocolsI2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN1.1, CAN2.0, CAN FD, LIN, FlexRay, MIL-STD-1553, AudioBus (I2S, LJ, RJ, TDM), USB1.x/2.0
     
    Measurement Tools
    Measurement FunctionalityDisplay up to 8 measurement parameters together with statistics, including mean, minimum, maximum, standard deviation, and total number. Each occurrence of each parameter is measured and added to the statistics table. Histicons provide a fast, dynamic view of parameters and waveshape characteristics. Parameter math allows addition, subtraction, multiplication, or division of two different parameters. Parameter gates define the// for measurement on the source waveform. Parameter accept criteria define allowable values based on range setting or waveform state.
    Measurement Parameters - Horizontal + JitterCycles (number of), Delay (from trigger, 50%), Δ Delay (50%), Duty Cycle (50%, @level), Edges (number of, @level), Fall Time (90-10, @levels), Frequency (50%, @level), Half Period (@level), Hold Time (@level), N Cycle Jitter (peak-peak), Number of Points, Period (50%, @level), Δ Period (@level), Phase (@level), Rise Time (10-90, @levels), Setup (@levels), Skew (@levels), Slew Rate (@levels), Time Interval Error (@level), Time (@level), Δ Time (@level), Width (50%, @level), Δ Width (@level), X(value)@max, X(value)@min
    Measurement Parameters - VerticalAmplitude, Base, Level@X, Maximum, Mean, Median, Minimum, Peak-to-Peak, RMS, Std. Deviation, Top.
    Measurement Parameters - PulseArea, Base, Fall Time (90-10, 80-20, @levels), Overshoot (positive, negative), Rise Time (10-90, 80-20, @levels), Top, Width (50%)
    Measurement Parameters - Statistical (on Histograms)Full Width (@ Half Max, @ %), Amplitude, Base, Peak @ Max Population, Maximum, Mean, Median, Minimum, Mode, Range, RMS, Std. Deviation, Top, X(value)@Peak, Peaks (number of), Percentile, Population (@bin, total)
     
    Math Tools
    Math FunctionalityDisplay up to 8 math functions traces (F1-F8). The easy-to-use graphical interface simplifies setup of up to two operations on each function trace, and function traces can be chained together to perform math-on-math.
    Math Operators - Basic MathAverage (summed), Average (continuous), Difference (-), Envelope, Floor, Invert (negate), Product (x), Ratio (/), Reciprocal, Rescale (with units), Roof, Sum (+).
    Math Operators - FiltersEnhanced resolution (to 15 bits vertical), Interpolate (cubic, quadratic, sinx/x), (SinX)/x.
    Math Operators - Frequency AnalysisFFT (power spectrum, magnitude, phase, power density, real, imaginary, magnitude squared), up to full record length. Select from Rectangular, VonHann, Hamming, FlatTop and Blackman Harris windows.
    Math Operators - FunctionsAbsolute value, Correlation (two waveforms), Derivative, Deskew (resample), Exp (base e), Exp (base 10), Integral, Invert (negate), Log (base e), Log (base 10), Reciprocal, Rescale (with units), Square, Square root, Zoom (identity).
    Math Operators - OtherSegment, Sparse
     
    Measurement and Math Integration
    Measurement and Math IntegrationHistograms to display statistical distributions of up to 2 billion measurement parameters. Trend (datalog) of up to 1 million measurement parameters. Track (display parameter vs. time, time-correlated to acquisitions) any parameter. Persistence histogram and persistence trace (mean, range, sigma)
     
    Pass/Fail Testing
    Pass/Fail TestingDisplay up to 8 pass/fail queries using a Single or Dual Parameter Comparison (compare All values, or Any value , ≥, within limit ±Δ value or %) or Mask Test (pre-defined or user-defined mask, waveform All In, All Out, Any In, or Any Out conditions). Combine queries into a boolean expression to Pass or Fail IF "All True", "All False", "Any True", "Any False", or groups or "All" or "Any", with following THEN Save (waveforms), Stop, Alarm, (send) Pulse, Hardcopy (send email, save screen image, save to clipboard, send to printer), or (save) LabNotebook.
     
    Display System
    SizeColor 12.1" widescreen flat panel TFT-Active Matrix with high resolution touch screen
    ResolutionWXGA; 1280 x 800 pixels.
    Number of tracesDisplay a maximum of 16 traces. Simultaneously display channel, zoom, memory and math traces.
    Grid StylesAuto, Single, Dual, Quad, Octal, Tandem, Quattro, Twelve, Sixteen, X-Y, Single+X-Y, Dual+X-Y
    Waveform RepresentationSample dots joined, or sample dots only
     
    Persistence Display
    Analog and Color-Graded PersistenceVariable saturation levels; stores each trace’s persistence data in memory
    Persistence TypesSelect analog, color, or three-dimensional
    Trace SelectionActivate persistence on all or any combination of traces
    Persistence AgingSelect from 500 ms to infinity
    Sweep Display ModesAll accumulated, or all accumulated with last trace highlighted
     
    Zoom Expansion Traces
    Zoom Expansion TracesDisplay up to 8 Zoom and 8 Math/Zoom traces
     
    Internal Waveform Memory
    Internal Waveform Memory4 active waveform memory traces (M1-M4) store 16 bit/point full length waveforms. Waveforms can be stored to any number of files limited only by the data storage media capacity.
     
    Setup Storage
    Front Panel and Instrument StatusStore to the internal hard drive, over the network, or to a USB-connected peripheral device.
     
    Automatic Setup
    Auto SetupAutomatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals
    Find Vertical ScaleAutomatically sets the vertical sensitivity and offset for the selected channel to display a waveform with the maximum dynamic range
     
    Calibration
    Calibration StabilityCalibration ensured within +/-5°C operating temperature. Manual calibration may be invoked if outside this temperature range.
     
    Processor/CPU
    TypeIntel® CoreTM i7-2710QE Quad, 2.1 GHz (3.0 GHz in turbo mode) (or better)
    Processor Memory16 GB standard
    Operating SystemMicrosoft Windows® 7 Pro 64 bit Embedded
    Oscilloscope Operating SoftwareTeledyne LeCroy MAUI™ with OneTouch
    Real Time ClockDate and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
     
    Connectivity
    Ethernet PortSupports 2 10/100/1000BaseT Ethernet interface (RJ45 ports)
    USB Host PortsMinimum 6 total (incl. 2 front panel) USB 2.0 ports support Windows compatible devices
    USB Device Port1 USBTMC port
    GPIB Port (optional)Supports IEEE - 488.2 (External)
    External Monitor Port15 pin D-Type WXGA compatible DB-15 to support customer-supplied external monitor.Includes support for extended desktop operation with WXGA resolution on second monitor.Supports touch screen integration of external monitor (Note: external display can not use a Fujitsu touch-screen driver).
    Remote ControlVia Windows Automation, or via LeCroy Remote Command Set
     
    Auxiliary Input
    Signal TypesSelect External Trigger or External Clock Input on the front panel
    Coupling50 Ω: DC; 1 MΩ: AC, DC, GND
    Max. Input Voltage50 Ω: 5 Vrms; 1 MΩ: 400 Vmax (DC + Peak AC ≤ 5 kHz)
     
    Auxiliary Output
    Signal TypesSelect from control signals or Off
    Output Signal500 Hz-1 MHz square wave or DC level; 50 mV-1 V into 1 MΩ
    Control SignalsTrigger enabled, trigger out, pass/fail status, off
    Connector TypeBNC, located on rear panel
     
    Probes
    Probes Qty. (4) ÷10 Passive Probes
    Probe SystemProBus. Automatically detects and supports a variety of compatible probes
    Scale FactorsAutomatically or manually selected depending on probe used
    Calibration OutputDefault is 1kHz square wave, 1Vp-p (typical), output to probe hook. Settable from 250 Hz to 1 MHz square wave; 50 mV to 1.0V.
     
    Power Requirements
    Voltage 100-240 VAC ±10% at 45-66 Hz; 110-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection; Installation Category 300 V CAT II
    Nominal Power Consumption200 W / 200 VA
    Max. Power Consumption320 W / 320 VA (with all PC peripherals and active probes connected to 4 channels)
     
    Environmental
    Temperature (Operating)+5 °C to +40 °C
    Temperature (Non-Operating)-20 °C to +60 °C
    Humidity (Operating)5% to 80% relative humidity (non-condensing) up to +31 °C.Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
    Humidity (Non-Operating)5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
    Altitude (Operating)Up to 10,000 ft. (3048 m) at or below +30 °C
    Altitude (Non-Operating)Up to 40,000 ft. (12,192 m)
    Random Vibration (Operating)0.31 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
    Random Vibration (Non-Operating)2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
    Functional Shock30 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
     
    Size and Weight
    Dimensions (HWD)11.48"H x 15.72"W x 5.17"D (291.7 mm x 399.4 mm x 131.31 mm)
    Weight12.9 lbs. (5.86 kg)
    Shipping Weight20.2 lbs. (9.2 kg)
     
    Certifications
    CE CertificationUL and cUL ListingCE Compliant, UL and cUL listed; conforms to UL 61010-1 (3rd Edition), UL 61010-2-030 (1st Edition)CAN/CSA C22.2 No. 61010-1-12,
     
    Warranty and Service
    Warranty and Service3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.